General Specifications As Per Brochure. To the best of our knowledge details below are deemed correct. It is the buyers responsibility to confirm prior to purchase. Equipped With: 2" Bar Capacity 15 HP Dual Opposing Spindles B-Axis & Dual Y-Axis for both Front and Backworking 36 Tool Positions w/ 18 Driven tools, 12 for B-Axis 80 gallon coolant tank Mistbuster 850 Mist Collector High Pressure Collant Edge Rebel V-65 Servo Bar Feeder Specifications: MAIN SPINDLE Integral Built-in Motor Spindle Maximum bar diameter: 2.008" Spindle Nose: A2-5 Collet size: Traub TRB-52 Maximum spindle speed: 6,000 RPM Servo Spindle motor horsepower: 15-HP peak, 10-HP 30-min. rated X1, Y1, Z1 AXIS X1, Y1, Z1 axis servo motor: X1-1.3 hp Y1/Z1-2.0 hp X1 axis travel: 10.63" Y1 axis travel: 18.11" Z1 axis travel: 9.84" Minimum programmable input: 0.00004" resolution X1, Y1, Z1 rapid travel rate: 1181 IPM (30m/min) MAIN SPINDLE TOOLING Number of driven tools: 6 axial and 6 radial driven Driven tool motor power: 5-HP Driven tool spindle speed: 6,000 RPM Driven tool collet size ER-20 (up to 1/2" tool shank) O.D. turning tools 5-20mm O.D. holders available I.D. boring tools 5-25mm I.D. bores available SUB SPINDLE Type: INTEGRAL BUILT-IN MOTOR SPINDLE Maximum bar diameter: 2.008" Collet size: Traub TRB-52 Maximum spindle speed: 6,000 RPM Servo Spindle motor horsepower 15-HP peak, 10-HP 30-min. rated X2, Y2, Z2 AXIS X2, Y2, Z2 axis servo motor: X2/Z2-1.3 hp/Y2-2.0 hp X2 axis travel: 18.89" Y2 axis travel: 18.11" Z2 axis travel: 10.63" X2, Y2, Z2 rapid travel rate: 1181 IPM (30m/min) Minimum programmable input: 0.0001" SUB SPINDLE TOOLING Number of axial driven tools: 3 axial, uses ER-20 collets Number of radial driven tools: 3 radial, uses ER-20 collets Driven tool motor power: 2.7-HP (2.0kw) Driven tool spindle speed: 6,000 RPM Driven tool collet size: ER-20 (up to 1/2" tool shank) O.D. turning tools: 4-20mm O.D. holders available I.D. boring tools: #4 - 25mm I.D. bores available COOLANT SYSTEM - 300 PSI Size: 80 Gallon tank, Pumps: 3 pumps with flow control ELECTRICAL REQUIREMENT 110-Amps,42kva,220 vac, 3 Phase AIR REQUIREMENTS: 85 psi, 20-cfm MACHINE WEIGHT: 12,345 LBS MACHINE DIMENSIONS: 142" x 85" x 82" w/ chip conveyor GenTurn 52-BY2 9-Axis Mill/Turn Center - Production Package 9-Axis Turning Center with B-Axis, and both Dual "Y" Axis & "C" Axis, including: 2-Traub-52 "Dead-Length" collet chucks. Automatic power shut-down. 36-Tool positions including 18-Driven Tools with ER-20 collet spindles included, Parts catcher with parts conveyor, chip conveyor, fluorescent worklight Barloader interface, headwall air blast and coolant outlets for main and sub spindle, Sub-Spindle programmable air blast, oil flush, and finished parts ejector 215 PSI High-Pressure coolant pump for cutting tools with coolant flow sensor monitor. Dual 1-HP coolant pumps for headwall & chip flush with coolant flow sensor monitoring.
to our home page