All Information From OEM Brochure Should Be Verified By Buyer: Equipped With (Standard): 6,000 RPM, 7.5 HP Mitsubishi Spindle Motor Coolant System with Coolant Flow Confirmation Sensing Switch Coolant Tank Mounted on Wheels for Easy Access for Clean-Out Hydraulic Closer System for a Non-Slip Grip on Work Holding Devices Manual Spindle Position Lock Plunger for Work Holding Changeover Foot Pedal Switch for Chuck Open/Close Control Full Machine Enclosure to Control Chips & Coolant Within the Machine MPG Hand Wheel Mounted on Operator Control Station Worklight and Full Splashguard Heat Exchanger for Electrical Cabinet Tri-Color Machine Condition Display Lamp Automatic Pressurized Centralized Lubrication System Parts Catcher - Pneumatically Actuated Collection Chute Under Spindle Parts Collection Drawer - Catcher Directs Parts to Drawer at Operators Knee Barfeed Interface Material Bar-Stop for Barfeeding Toolholders for up to 9-Cutting Tools 2-Dual Tool Holders for 2-Axial or 1-Cross OD Tool. For up to 4 OD Tools. 1-Dual Tool Holder for 2-Axial Mounted Tools 1-Single & 2-Dual 25mm Bore ID Tool Holders for a Total of 3 ID Tools 5-Piece 25mm Bushing Set for ID Tool Holders - 8, 10, 12, 16, 20mm Bushing Specifications: Axis Travel X-Axis: 8.46" (215mm) Z-Axis: 5.98" (152mm) Turning Diameter/Length: 7.87"/5.5" (200mm/140mm) Swing Over Bedways: 12.59" (320mm) Axis Feeds Rapid Traverse (X,Z): 787 IPM 20/20m/minute Rated Cutting Feedrate: 236 IPM 6/6m/minute Mechanical Way System (X,Z): Box Ways Turcite Slant Bed Angle: 20 Deg. Slant Bed Angle Axis Drive Motor Power (X): 1.0HP .75kw Axis Drive Motor Power (Z): 1-1/3 HP 1.0kw Ballscrew Diameter (X,Z): 32mm Positioning Accuracy (X,Z): +0.00015" +0.004mm Positioning Repeatability (X,Z):+0.00008" +0.002mm Least Input Command Increment: 0.0001"/0.00004" 0.001mm Spindle Spindle Nose Mount: A2-5 Spindle Speed: 6,000 RPM Tapping Spindle Speed: 2,000 RPM Bar Capacity: 1-1/4" 32mm Spindle Bore: 34mm Spindle Bearing - ID: 70mm (80mm Optional) Spindle Motor Power: 7.5 HP 5.5kw (10HP/7.5kw Opt.) Spindle Motor Torque: 26 ft.lbs 35Nm Spindle Motor Drive Coupling: Belt Drive Spindle Runout: <0.000040" TIR Tooling Plate & Tool System Tool Plate Overall Dimensions: 8.66" x 36.45" 220mm x 706mm Tool Plate T-Slot Dimensions: 21mm Base & 12mm Neck Width (8mm Base Height / 17mm Total) T-Slots: 3 T-slots on 63mm Centers Turning Tool Shank Size: 20mm 3/4" Square Shank Internal Tool Shank Size: 32mm 1-1/4" (25mm Opt.) Optional Driven Tool Collet Size (1/2"): 1 HP Optional Driven Tool Horsepower (.75kw): 2-ER20 Collets General: Air Service Requirements: 85 PSI @ 5-scfm 5.5Kg/cm Electrical Requirements: 10kva, 28-Amps 220vac/+5%/60 HZ Coolant Tank/Motor Power: 21 Gallons/ 1/2 HP 80 Liters/2-Amps Lubrication Pump: 150 Watts Hydraulic Pump Motor/Pressure: 1 HP/500 PSI .75kw/32-Bar Floor Space Requirements: 81" x 64" x 64" 282x135x183cm Machine Weight: 4,850 lbs 2,200 kg Warranty - 1-Year Machine Warranty & 3-Year Mitsubishi Control/Motors/Drive MACHINE OPTIONS Factory machine installation: "Peace-of-Mind Factory Installation" - includes expenses: $2,995.00 Factory on-site 3-day machine operation and program training - includes expenses: $3,995.00 Second-year machine warranty: $2,995.00 Parts Conveyor for finished parts: $2,490.00 Belt-Style Chip Conveyor & Chip Cart - Rear Discharge: $3,995.00 C-Axis: $3,995.00 2-Position 1-HP ER-20 Face-Drilling Servo Driven Live Tools (details shown under options): $5,990.00 2-Position 1-HP ER-20 Side-Drilling Servo Driven Live Tools (details shown under options): $6,790.00 Single I.D. Tool Holder: $260.00 Double I.D. Tool Holder: $390.00 Single O.D. Tool Holder: $260.00 Double O.D. Tool Holder: $390.00 8-Station Hydraulic Turret, 0.3-second index, 20mm box tools, 32mm I.D. bores w/3-tool drill block: $3,995.00 Voltage Stabilizers and Transformers (specify voltage needs):POR Dunham air cylinder actuator (for thin-wall parts: POR Coolant Chiller System-12,000 BTU's for higher accuracy applications $4,495.00 Chuck Air Blow system: $390.00 Air Conditioner upgrade for electrical cabinet (upgrade over standard heat exchanger): $2,490.00 CHUCKS & COLLET HOLDERS *Note: No working holding device comes with this machine, order below* 6" 3-Jaw Hydraulic Chuck: $1,995.00 5C Collet Chucks: $1,695.00 Collet Chucks for: 5C, 16C, 2J, 3J, 22J, Brown & Sharpe #21 & #22 Collets POR TOOLING CERTIFICATES For Collets, Bushings, Bore Bar Sleeves, Spindle liners, cutting tools, machine options etc. $2500 Tooling Certificate $5000 Tooling Certificate $10,000 Tooling Certificate TRAINING & TERMS OF SALE Lifetime FREE Training: Ganesh Machinery offers a 3-day training program for all production CNC machines at our training center. The intense training program includes basic manual programming, machine setup, operation, and operator level maintenance for those with a working knowledge in the programming & setup of CNC machines. Training does not cover CAD/CAM systems or Manual Guide-i type of programming. There is no charge for the training program at Ganesh for our customers. Turn-key projects and on-site training are an available option charged at the prevailing hourly rate. Warranty: 1 full year Ganesh parts and labor warranty on the machine and 3- years CNC control & drives. Service and Parts: Ganesh or your authorized Ganesh trained servicing dealer provides installation and service. Spare parts are stocked at Ganesh in Chatsworth to support your continued machine operation. F.O.B. Point: Machines ship F.O.B. Ganesh Machinery from Chatsworth, CA 91311 Payment Terms: 20% down payment with your Purchase Order secures the machine. 70% is due prior to machine shipment, and the 10% balance is due net-30 days after installation. Or the machine can be financed with a Ganesh approved lender. Leases with $1.00 buyout are available upon approved credit. Delivery Schedule: Delivery is stock to 12-weeks, subject to prior sales. Purchase is governed by the Ganesh Machinery terms and conditions of sale. UL & TV ELECTRICAL APPROVAL IS AN AVAILABLE OPTION Prices and specifications subject to change without prior notice.
to complete inventory display
to our home page