34.64"X, 23.62"Y, 25.59"Z, Ganesh 5X-12, 2018, 12,000 RPM Mits M830 Control   Our stock number: 400442

All Information From OEM Brochure Should Be Verified By Buyer:

Equipped With:
 Heidenhain Glass Scale Feedback on all 5-Axes 
 "Big-Plus" Dual-Contact #40-Taper Spindle
 Chip Wash Down Coolant System 
 300 PSI (20-Bar) "Through-the-Spindle" Coolant System
 Full Machine Enclosure with Top Covers (precut for exhaust duct)
 Spindle Air Blast by M-Code
 Spindle Oil Cooler - Thermostatically controlled
 Remote Operator MPG Hand wheel
 High Speed Synchronous Rigid Tapping
 Dual LED High-Intensity Worklamps
 32GB Solid State Data Server
 32GB USB & SD Memory Card Slots and Ethernet connectivity
 Machine Condition Signal Lamp
 Tramp-Oil Coolant Recovery System
 6-Thru-Tool-Coolant Pull Studs

Axis Travel
 X-Axis:                              34.64"             880mm
 Y-Axis:                              23.62"             600mm
 Z-Axis:                              25.59"             650mm
 Spindle to Rotary Table Surface:     4.72-18.89"        120-480mm
 Spindle Center to Z Way Covers:      22.44"             570mm (Troat)

Tilting Rotary Table
 Platter Diameter:                    12.6"              320mm
 Center Bore Diameter:                50 H7
 T-slot Width / Number:               12H7/4
 Guide Block Width:                   18mm
 Maximum Part Swing:                  16.3"
 Maximum Work Table Load:             220 lbs            75kgs

Spindle
 Spindle Motor:                       25 HP S3 Power     20HP 30-Min

 Spindle Speed:                       12,000 RPM         (15,000 Optional)
 Spindle Torque:                      90ft-lb @1,500 RPM
 Tool Type:                           CAT #40 Taper      BT#40 Optional
 Retention System/Holding Capability  BellVille Spring Stack (1650-1760 lbs)
 Spindle Runout:                      <0.000040" TIR
 Spindle Bearings - Rear:             110mm NSK70BNR     2-P4 Class 7 Bearing
 Spindle Bearings - Front:            110mm NSK70BNR     2-P4 Class 7 Bearing
 Retention Knob:                      C40-4502H (Coolant)

Axis Feeds
 Rapid Traverse (X,Y):                1,417 IPM          36m/minute
 Rapid Traverse (Z):                  1,260 IPM          32m/minute
 Cutting Feedrate:                    0.02-393 IPM       10m/minute
 Axis Drive Motor Power (X,Y,Z):      5-HP               3.5 kw
 Ballscrews (X,Y,Z):                  40mm Ballscrews    12mm Pitch
 Least Input Command Increment:       0.0001"/0.000040"  0.001mm(40 Millionth)
 Accuracy X,Y,Z Axis (JIS6338):       +0.0002"/12"       +0.005mm Over 300mm
 Repeatability X,Y,Z Axis (JIS6338):  +0.0001"/12"       +0.003mm Over 300mm

Tool Changer
 Tool Capacity (40+1):                40 Tool Twin Arm   Chain Drive Rack
 Tool Shank:                          CAT#40 Taper       BT#40 Optional
 Tool Change Time:                    1.7 Seconds Tool to Tool
 Tool Diameter / w/adjacent tool:     5.90" / 3.15"      150mm/80mm
 Tool Length/Weight (from gage line): 11.81" / 15 lbs    300mm/7Kg
 Tool Selection/Tool Access           Random             Bi Direction: 

General
 Coolant Capacity:                    97-Gallons         256 Liters
 Electrical - Connected Load:         50 amps            220vac+5%, 60hz
 Air Service Requirements:            85 PSI @ 14-scfm
 Machine Dimensions:                  115" x 82" x 116"  306x231x256cm
 Machine Weight:                      15,708 lbs         7,120 kg

Built In Tilting Rotary Trunnion Drive System Specifications
 Platter Diameter:                    12.6"              320mm 
 Center Bore Diameter:                50mm H7
 T-Slot Width:                        12mm H7
 Guide Block Width:                   18mm
 A-Axis Tilting Servo Motor:          Mitsubishi HF-224T
 C-Axis Rotary Servo Motor:           Mitsubishi HF-104T
 Torque:                              7 Kg-cm
 Indexing Resolution:                 0.001 Degrees
 Indexing Accuracy, A / C:            50 Sec/20 Sec
 Indexing Repeatability, A / C:       +4 Sec / +3 Sec
 Feedback System A / C:               Heidenhain Encoder (ECN-223M w/ 10 sec.

                                      resolution)
 Work Load Capacity:                  165 lbs            75kg Horizontal
 Transmission Ratio A / C:            1:120/ 1:90 
 Tilting Angle Range:                 +30 - -120 Degrees
 Brake Torque A / C:                  140 ft lbs
 Cutting Torque Limit:                25 Kg/m
 Rotational Speed A / C:              25 / 25 RPM
 Work Load Capacity:                  330 lbs            75kg In Tilt 


*Machine Options*

 Upgrade to 5-Axis Simultaneous Operation w/ Mitsubishi M850 Control
                                                         $16,500.00

Factory machine installation: "Peace-of-Mind Factory Installation" - Includes

Expenses:                                                $2,995.00

Factory On-Site 3-Day Machine Operation and Program Training - Includes

Expenses:                                                $3,995.00

Belt Type Chip Conveyor w/ 38" Barrel Height Discharge:  $3,990.00

15,000 RPM Spindle Speed Upgrade:                        $5,995.00

24,000-rpm HSK-63 Integral Spindle 
w/ Ceramic Bearings & Spindle Chiller:                   POR 

Second-Year Machine Warranty:                            $6,995.00

Voltage Stabilizers/Transformers 
(specify voltage needs):                                 POR

1,000 PSI Through-The-Spindle Coolant Upgrade:           $9,990.00

For Collets, Vises, Cutting Tools, Machine Options Etc.
$2500 Tooling Certificate  
$5000 Tooling Certificate  
$10,000 Tooling Certificate  
 
*See the Genmill Options Brochures for a Complete Listing of Tooling Options*

TRAINING & TERMS OF SALE 

Lifetime FREE Training:
Ganesh Machinery offers a 3-day training program for

all production CNC machines at our training center. The intense training

program includes basic manual programming, machine setup, operation, and

operator level maintenance for those with a working knowledge in the

programming & setup of CNC machines. Training does not cover CAD/CAM systems

or Manual Guide-i type of programming.  There is no charge for the training

program at Ganesh for our customers.  Turn-key projects and on-site training

are an available option charged at the prevailing hourly rate.  

Warranty:
1 full year Ganesh parts and labor warranty on the machine and 3-

years CNC control & drives.

Service and Parts:
Ganesh or your authorized Ganesh trained servicing dealer

provides installation and service.  Spare parts are stocked at Ganesh in

Chatsworth to support your continued machine operation.

F.O.B. Point: Machines ship F.O.B. Ganesh Machinery from Chatsworth, CA 91311


Payment Terms:

20% down payment with your Purchase Order secures the machine.

70% is due prior to machine shipment, and the 10% balance is due net-30 days

after installation.  Or the machine can be financed with a Ganesh approved

lender.  Leases with $1.00 buyout are available upon approved credit.  

Delivery Schedule: Delivery is stock to 12-weeks, subject to prior sales.

Purchase is governed by the Ganesh Machinery terms and conditions of sale.

UL & TV ELECTRICAL APPROVAL IS AN AVAILABLE OPTION

Prices and specifications subject to change without prior notice.


Get a Quote

Company:
Contact:
Email:
Tel:
Address:
City St ZIP:
Fax:

How did you hear of us?
Additional information on your request:
   

Please enter text from above:

RETURN to complete inventory display       RETURN to our home page